Amana GUC Series Manual de instrucciones

AmanaFayetteville, TN 37334!RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.ATTENTION INSTALLING PERSONNELAs a professional installer you have an obligat

10HORIZONTAL VENT/INTAKE TERMINATIONS12" Min.Vent24" Max.3" Min.12" Min.Screen24" Max. AirIntake 90°Medium RadiusElbow

11Do not point terminals into window wells, stairwells, al-coves or other recessed areas. It is preferable for the airintake to terminate on opposite

12structure as shown in Figures 6, 8, and 9 are not to becounted when using Tables 1 through 3. The additional two90° elbows as shown in Figure 7 must

13# ofInside5-10 10-15 15-20 20-25 25-30 30-35 35-40 40-45 45-50 50-55 55-60 60-65 65-70 70-75 75-80 80-85 85-90ElbowsFeet Feet Feet Feet Feet Feet Fe

14VIII. Gas PipingThe rating plate is stamped with the model number, type ofgas and gas input rating. Make sure the furnace is equippedto operate on t

15Natural Gas Capacity of PipeIn Cubic Feet of Gas Per Hour (CFH)Length of Nominal Black Pipe SizePipe in Feet 1/2" 3/4" 1" 1 1/4"

16When the gas piping enters through the right side of thefurnace (Figures 16 and 17) the installer must supply thestraight pipe to reach the exterior

17TANKS AND PIPING - PROPANE GAS UNITSWARNINGTo prevent death, personal injury orproperty damage due to fire or explosioncaused by a propane gas leak,

18IX. Electrical WiringWARNINGTo avoid the risk of electrical shock, wiringto the unit must be properly polarized andgrounded.WARNINGTo avoid electric

19Control ModuleCoolHeatParkParkLineTransformerEACHumCirLineTransformerEACHumHot 120 VACNeutral120 VACAir CleanerHumidifierOptional Accessories{Figure

2To The OwnerIt is important that you fill out the owner’s registration cardand mail it today. This will assist Amana in contacting youshould any serv

20Timing Chart for Normal Integrated Ignition Control OperationOnOffOpenClosedClosedOpenOnOffOnOffOnOffSeconds 0 17 20 23 53

21When the furnace is heating, the temperature of the returnair entering the furnace must be between 55°F and 100°F.XI. Sequence of OperationNORMAL HE

22CAUTIONThe cause must be investigated by aqualified servicer before any attempt ismade to engage the roll-out protectiondevice and turn the furnace

23Figure 25White Rodgers Model: 36E36 or 36E37Figure 26Honeywell Model: VR-8205White Rodgers Model 36E22 or 36E23: Push theselector switch to "OF

24GUD MANIFOLD PRESSUREWARNINGTo prevent death or personal injury due tocarbon monoxide, all hoses must beconnected as shown in Figure 28. Failureto c

25On GUD models, the flame may be inspected through theobservation window on the front cover of the burner box.Check the burner flames for: 1. Good ad

2621OFFLow VoltageConnectionsFan OffAdjustmentsFigure 31Ignition Control(Viewed in an Upflow Installation)60SecondDelay12ONOFFB1B2B3B490SecondDelay12O

27Grasp the lower portion of the filter, lift up to disengage itfrom the lower railing, move towards blower, drop filterdown. Pull filter outward (Fig

28CONDENSATE DRAINAGE SYSTEM (QUALIFIEDSERVICER ONLY)The drain tubes, standpipe, and field-supplied drain linemust be check annually and cleaned as of

3SAFETY• When the furnace is heating, the return air tempera-ture of the furnace must be between 55°F and 100°F.• Furnaces installed in areas frequent

4LOCATION• Centralize the furnace as is practical with respect tothe air distribution system.• The furnace must be set on a level floor to enable thec

5age or restriction, leakage, corrosion and otherdeficiencies which could cause an unsafe condition.(c) Insofar as is practical, close all building do

6tion ventilation and dilution of flue gases. However, inbuildings of tight construction (for example, weatherstripping, heavily insulated, caulked, v

73. When communicating with the outdoors throughhorizontal ducts, each opening shall have a mini-mum free area of 1 square inch per 2,000 BTU perhour

8must terminate at least one foot outside to keep moistcombustion products away from the structure. The venttermination must be at least three feet ab

9tight where it penetrates the roof with a proper flashingsuch as used with a plastic plumbing vent. The vent maybe run through an existing unused ch