AMANA®FOUR BURNER GAS GRILLAssembly/Installation Instructions and Use & Care GuideFor questions about features, operation/performance, parts, acce
4. Repeat step 1-2 to install the cart side right in position.5. Place the cart back onto the grill cart base. Place two wheel channel assembly bolts
116. Place the cart middle shelf onto the cart base.7. Use three (3) self-tapping screws to secure the cart middle on the cart base.8. Use three (3) s
129. Use two (2) self-tapping screws to secure the middle bracket onto the cart side left.Note: Install the self-tapping screws from outside of cart s
1. Take the side burner package out from inside the grill head.2. Tilt the grill head on its back and loosen the four (4) grill mounting bolts so that
ASSEMBLY INSTRUCTIONSStep 4: Assemble Drawers1. With a Phillips head screwdriver, remove the two phillips pan head screws from the handle, then attach
ASSEMBLY INSTRUCTIONSStep 4: Assemble Drawers (Cont.)5. Align the slides (attached to the drawer) with the front ends of the slide rail assemblies (at
7. Take the other drawer, align the slides (attached to the drawer) with the front ends of the slide railassemblies (attached to the cart).Note: Make
ASSEMBLY INSTRUCTIONSStep 5: Assemble Cart Door1. Remove the two phillips pan head screw on the cart door handle and use these two screws toinstall th
18ASSEMBLY INSTRUCTIONSStep 6: Assemble Side Shelf Left1. Loosen the Four (4) 5/16-24 hex head screws located on the left grill side.2. Attach the lef
1. Open side burner cover.2. Remove the brass burner cap attached with tape along with side burner grate and set aside.3. Loosen the four (4) 5/16-24
TABLE OF CONTENTS2OUTDOOR GRILL SAFETY...3-4U
ASSEMBLY INSTRUCTIONSStep 8: Assemble the Side Valve & igniter module1. Unscrew the igniter button cap and the plastic nut from the igniter module
ASSEMBLY INSTRUCTIONSStep 9: Assemble the Side Burner Casting1. Remove the two phillips pan head screws from the side burner casting.2. Angle the side
ASSEMBLY INSTRUCTIONS1. Use the two (2) screws removed in step 1 on page 21 to secure the head of side burner casting onthe rear bracket.2. Use the tw
ASSEMBLY INSTRUCTIONSStep 10: Assemble Igniter WiresAA. Igniter moduleB. Side burner igniter wireC. Main burner igniter wiresBC1. Connect loose ignite
ASSEMBLY INSTRUCTIONSStep 11: Assemble the Side Burner Accessories1. Center the brass burner cap on top of the side burner head.2. Place the side burn
ASSEMBLY INSTRUCTIONSStep 12: Assemble the Drip Pan1. Pull out the top drawer.2. Open the right cart door.3. Slide the drip pan onto the drip pan guid
26ABCA. Flavor gridsB. Main cooking gratesC. Bread warming rack1. Insert the flavor grids into the cutouts with triangle ridges facing up.2. Install m
27INSTALLATION REQUIREMENTSSelect a location that provides minimum exposure to wind and traffic paths. The locationshould be away from strong draft ar
Product Dimensions53.625”(136.3cm)45”(114.4cm)33.875”(86.1cm)29”(73.8cm)13.125”(33.4cm)21”(53.3cm)20.2”(51.3cm)Observe all governing codes and ordinan
Gas Supply Line Pressure TestingTesting above ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):The grill and its individual shutoff valve must be dis
OUTDOOR GRILL SAFETYYour safety and the safety of others are very important.We have provided many important safety messages in this manual and on your
30OUTDOOR GRILL USEControl PanelOFFPUSH&TURNHLMOFFPUSH&TURNHLMOFFPUSH&TURNHLMABCEDA. Left burner control knobB. Middle Left burner control
Using Your Outdoor Grill (cont.)Manually Lighting Grill1. Do not lean over the grill.2. Remove the manual lighting extension and attach a match to the
TIPS FOR OUTDOOR GRILLING32Before Grilling Thaw food items before grilling. Lightly oil the grill grates or the food when cooking low-fat cuts of me
OUTDOOR GRILL CAREReplacing the Igniter BatteryIf igniters stop sparking, the battery should be replaced.1. Unscrew igniter button cap counter clockwi
34OUTDOOR GRILL CARE (Cont.)General Cleaning (Cont.)WARMING SHELFCleaning Method: Liquid detergent or an all-purpose cleaner. Rinse with clean water
35OUTDOOR GRILL CARE (Cont.)General Cleaning (Cont.)DRIP PAN AND SHELFIMPORTANT: The drip pan should only be removed when grill is completely cool.The
TROUBLE SHOOTINGGrill will not light Is the 20 lb LP gas fuel cylinder valve turned off?Turn the 20 lb LP gas fuel cylinder on. Is the grill properl
37REPLACEMENT PARTSHood Assembly Front Face OverlayFCTG2908001 FCTG29080061 set 1 setHood Handle Amana LogoFCTG2908002 FCTG26080081 pcs 1 pcsTemp Guag
38Side Burner Valve Cart side rightFCTG2608032 FCTG290800161 pcs 1 setCart back Wheel channel leftFCTG2908010 FCTG29080171 set 1 setCart door right as
Side Burner Right Assy. Side burner igniter with wireFCTG2908022 FCTG26080301 set 1 pcsIgniter Module 5 polesFCTG29080271 pcsSide Burner GrateFCTG2707
IMPORTANT SAFETY INSTRUCTIONSIMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used atelevations above 2000 ft (60
AMANA® is a registered trademark of Maytag Corporation or its related companies and is used under license toSure Heat Manufacturing© 2008.All rights r
1. Using a utility knife, cut the tape to open top flaps ofcarton.2. Remove Assembly/Installation Instructions and Use andCare Guide.3. Remove the lar
Assembly Hardware Supplied 38 - self-tapping screws 1 - Side burner knob with bezel 1 - “AA” batteryNOTE: Other hardware required is attached to th
ASSEMBLED GRILL VIEWABCFDEGHIJA. Control knob: main burnersB. Side shelfC. Grilling/cooking surfaceD. Roll top grill hoodE. Hood handleF. Bread warmin
ASSEMBLY INSTRUCTIONSStep 1: Assemble Wheel Channels1. Remove the four (4) caster assembly nuts and two (2) bolts from the wheel channel assemblies.No
Step 2: Assemble Grill Cart1. Place the cart side left onto the two (2) outer caster assembly bolts, make sure the largeflange is toward the front of
Comentarios a estos manuales